pdf Installation Instructions (PDF) (4.54 MB)

Installation Video 

 Overview

  • BlockShield SA Plus is a self-adhered, non-asphaltic air and vapor barrier roofing underlayment designed for applications either direct to deck, or over a thermal barrier board or structural concrete.*
  • BlockShield SA Plus is made from a proprietary high strength polypropylene sheet with a very aggressive adhesive layer that effectively bonds to virtually all deck types.
  • BlockShield SA Plus can be installed on steep slope roofs (>2”:12”) and on low slope roofs (1/4":12" <2":12") in both commercial and residential construction.
  • Top surface is slip resistant, UV stable, and resistant to punctures, tears, and foot traffic.

*See installation instructions for concrete substrates

LowSlope Sidebyside Install WebImages

Product Applications

  • Apply directly to galvanized or painted steel Type B Deck
  • Apply to thermal board fastened to galvanized steel deck
  • Plywood
  • Gypsum
  • Structural Concrete*

Safety

  • CAUTION: Release liners are slippery. To prevent injury, liner should be removed from under foot as soon as membrane is installed and disposed of properly.
  • Persons who access any roofs, involved with roof construction, repair or maintenance shall use appropriate personal protective equipment including, but not limited to, hard hats, eye protection, and leather gloves and must be trained on safe practices relevant to their work.
  • Where the use of ladders, scaffolds, platforms, or temporary floors are utilized, safety lines and safety harnesses shall be used. Please access the OSHA Web site at www.osha. gov, contact your local OSHA office, or visit the local federal bookstore to obtain the most current information on OSHA 29 CFR 1926.

Delivery, Packaging And Storage

  •  Store material in original packaging.
  •  Protect rolls from direct sunlight and inclement weather until ready for use.

Substrate Preparation

  • Steel surfaces must be clear of any oil residue and moisture.
  • Wood decks must be dry to the touch and clear of dirt and dust.
  • Prime structural concrete as required.
  • Ensure substrate fasteners are flush with surface and fastened into solid backing.
  • Install in temperatures 20°F (-6.6°C) and rising.

Limitations

  • Cover BlockShield SA Plus within 180 days of installation with permanent roofing material.
  • If desired adhesion is not attained between membranes due to site conditions, VaproShield recommends applying a bead of VaproBond as an additional solution to pressure rolling.

Installation Best Practices Galvanized Steel B Deck

BlockShield Roof Flat Installation step 1 041323 BestPractice web images 02

STEP 1
Starting at the low point of the roof, unroll BlockShield SA Plus onto the clean, dry steel deck.

Once BlockShield SA Plus is in place, while holding the sheet tight, remove the silicone release film by pulling diagonally.

STEP 2
When installing subsequent rolls of BlockShield SA Plus ensure 3” (7.5 cm) side laps are maintained.

After multiple rolls are installed, roll the membrane  with a weighted roller, min. 70 lbs.

CAUTION: Release liners are slippery. To prevent injury, liner should be removed from under foot as soon as membrane is installed and disposed of properly.

BestPractice web images 03

STEP 3
At the head lap the installation of a metal sheet is required to support the head lap between flutes. Ensure 3" (7.5 cm) head laps are maintained on metal sheet plate for each course during installation.

BlockShield Roof Flat Installation 4 022723

STEP 4
Cover as soon as possible to limit exposure to UV and construction traffic. When left exposed to precipitation, positive slope and adequate drainage is required. The effects of weathering may vary based upon local climate and project conditions. May be used as temporary protection at the discretion of the general contractor or building professional. Maximum exposure is 180 days prior to coverage.

CAUTION: Release liners are slippery. To prevent injury, liner should be removed from under foot as soon as membrane is installed and disposed of properly.

Installation Best Practices Structural Concrete

Flat Roof Concrete exploded 2 062323 Webcrop

 

Flat Roof Concrete exploded 2 062323 Webcrop
STEP 1
1A: Concrete deck installed by others.
STEP 2
2A. Prime surface as required. Contact VaproShield Technical for primer requirements.
BlockShield Roof Concrete Installation 1 063023 Web BlockShield Web assets 01

CAUTION: Release liners are slippery. To prevent injury, liner should be removed from under foot as soon as membrane is installed and disposed of properly.

STEP 3
3A. Starting at the low point of the roof unroll BlockShield SA Plus onto the primed surface.
3B. Once placed, while holding the sheet tight, remove the silicone release paper. Remove release paper from under foot.

STEP 4
4A. Install subsequent rolls of BlockShield SA Plus ensure a 3” min. (7.5 cm) side laps are maintained.

4B. After multiple rolls are installed, roll the entire section of installed membrane with a weighted roller, min. 70 lbs.

BlockShield Web assets 02
STEP 5
5A. At the end of each roll, ensure 3" (7.5 cm) head laps are maintained.
BlockShield Roof Concrete Installation 4 063023 Web

STEP 6
Cover as soon as possible to limit exposure to UV and construction traffic. When left exposed to precipitation, positive slope and adequate drainage is required. The  effects of weathering may vary based upon local climate and project conditions.

May be used as temporary protection at the discretion of the general contractor or building professional.

Maximum exposure is 180 days prior to coverage.

REGISTER FOR OUR WEBINARS TODAY